The cost of a house pad in Texas comes down mostly to how many yards of select fill it takes and how that fill is placed and tested. A 3,000-square-foot pad built 2 feet high needs about 222 cubic yards of compacted fill (roughly 255–265 yards delivered once you allow for compaction). On top of the material you pay for spreading and compacting in lifts, compaction testing, and usually a geotechnical report, which national cost guides put at about $1,000–$5,000 for a home site.
What Is a House Pad?
A house pad (or building pad) is a raised, level, compacted platform of soil that the foundation is formed and poured on. It sets the finished floor elevation, gives the slab uniform support, and on Texas clay it also acts as a buffer between the slab and soil that shrinks and swells with moisture. Most pads in North and Central Texas are built from select fill: a sandy clay with a low plasticity index (PI) that compacts well and moves far less than native black clay.
How Much Fill Does a House Pad Take?
Pad volume is length × width × height ÷ 27. The table gives compacted volumes for common pad footprints. Pads usually extend a few feet past the slab on every side, so size the pad to the footprint on your plans, not the house square footage.
| Pad footprint | Area | 1 ft high | 2 ft high | 3 ft high |
|---|---|---|---|---|
| 30 × 40 ft (shop or small home) | 1,200 sq ft | 44 yd³ | 89 yd³ | 133 yd³ |
| 40 × 50 ft | 2,000 sq ft | 74 yd³ | 148 yd³ | 222 yd³ |
| 50 × 60 ft | 3,000 sq ft | 111 yd³ | 222 yd³ | 333 yd³ |
| 60 × 70 ft | 4,200 sq ft | 156 yd³ | 311 yd³ | 467 yd³ |
| 70 × 80 ft | 5,600 sq ft | 207 yd³ | 415 yd³ | 622 yd³ |
Two adjustments before you order:
- Compaction allowance. These are compacted, in-place volumes. Loose fill delivered by truck compacts down, so order roughly 15–20% more for a compacted structural pad. The exact factor depends on the material and the density spec.
- Side slopes. The table is a straight-sided box. Real pads have sloped edges, and on a 2- or 3-foot pad those slopes add real volume. Your plans or the pad builder will account for it.
Run your own numbers with the cubic yard calculator, or use the fill dirt calculator to see a delivered price.
House Pad Cost Breakdown
| Item | Typical range | Source / basis |
|---|---|---|
| Select fill, delivered (DFW) | Starting at $20/yd from us; Texas market roughly $12–$30/yd depending on area | Our published price; supplier listings |
| Geotechnical (soils) report | About $1,000–$5,000; averages near $2,700–$2,900 | HomeGuide, Angi |
| Equipment and operator for spreading and compacting | About $100–$300 per hour | HomeGuide excavation rates |
| Compaction (density) testing | Billed per visit or per test by the testing lab; varies widely | Ask the lab your engineer names |
| Clearing and stripping the pad area | Quoted per site | See land clearing cost per acre |
Worked material example: a 50 × 60 ft pad, 2 feet high, is 222 compacted yards. With a 15% allowance that is about 255 delivered yards, or 16 tri-axle loads. At our DFW starting price of $20 per yard for select fill, the material comes to about $5,100 delivered. Placement, compaction, testing and the soils report are on top of that, and they vary by site.
What Drives House Pad Cost?
Pad height
Height multiplies everything. Each additional foot on a 3,000-square-foot pad adds about 111 compacted yards. Pad height is set by the plans: the finished floor usually has to sit a certain height above surrounding grade and, where there is a floodplain, above the flood elevation by a margin the city sets. It may also be set by the soils report, which can require removing a layer of native clay and replacing it with select fill.
The soils report
On expansive Texas clay, the geotechnical report usually drives the pad spec: how much native soil to remove or moisture-condition, what PI range the select fill must meet, lift thickness, and the density target (often stated as a percentage of Standard Proctor density). Builders and lenders frequently require one. The report is what the pad gets built to; a pad contractor does not set those numbers.
Compaction and testing
Pads are built in lifts, typically 6–8 inches at a time, each one moisture-conditioned and compacted before the next goes on. A testing lab checks density on the lifts the engineer specifies. Failed tests mean rework, so moisture control matters as much as the roller.
Site conditions
Trees and roots under the pad area have to come out first. A wet site, poor truck access, or a lot that needs a lot of cut and fill to balance all add time. When a site has dirt to spare (from a pond or driveway cut, for example) and it meets the spec, using it can lower import costs.
Is Select Fill Required for a House Pad in Texas?
There is no single statewide rule. The requirement comes from the foundation design and the soils report for your lot. In DFW, select fill or a select fill cap over moisture-conditioned native clay is the common spec because the native black clays move so much. Plain fill dirt is fine for raising yard grades, but not as structural pad material unless the engineer approves it. Read more in our Texas clay soil guide.
Get a House Pad Bid
We supply select fill and build pads across DFW to the elevation, lift and density spec on your plans or geotechnical report. Pad building is quoted per job: upload your plans and soils report through the bid form on our building pads page. If you only need the material, text (469) 253-2403 with the yardage and address.