See today’s confirmed same-day availability, or text (469) 253-2403 for instant pricing
Fill Dirt Near Me

What Is Select Fill? Specs, Uses and How It Differs From Structural Fill

Updated November 2026

Select fill is a sandy clay or clayey sand with a controlled plasticity index (PI), typically somewhere around 6 to 20 in North Texas specifications, chosen because it compacts tightly and swells very little when it gets wet. It is the material geotechnical engineers specify under slab foundations, building pads and flatwork when the native soil is expansive clay. In DFW, select fill is delivered starting at $20 per cubic yard, and in Denver starting at $25 per cubic yard (10-yard minimum).

What makes fill "select"?

"Select" means the material has been picked to meet a written specification, not just dug from the nearest hole. A typical North Texas select fill spec controls three things:

  • Plasticity index (PI): a lab measure of how much a soil's behavior changes with moisture. Select fill specs commonly require a PI with a floor of about 4–8 and a ceiling of about 15–20. The floor keeps enough clay in the mix to bind and compact; the ceiling keeps swell potential low.
  • Liquid limit (LL): often capped somewhere around 35–40.
  • Gradation and debris: no rocks over a stated size (often 2–4 inches), no organics, no trash, no construction debris.

The exact numbers come from the soils report for your site. One engineer may write "PI between 6 and 15," another "PI between 8 and 20, LL under 40." Follow the report you were given, not a number from the internet, including this one.

Why North Texas uses so much select fill

Much of DFW sits on high-plasticity clay (Houston Black, Austin chalk-derived clays and similar), with PI values that commonly run well over 30 and sometimes over 40. That clay can swell several percent when it soaks up water and shrink back when it dries, which is what cracks slabs and racks door frames. Engineers counter it in a few ways, and one of the most common is to remove or cap the top few feet of native clay with a layer of low-swell select fill. The select fill acts as a buffer that does not move much with the seasons. For the full background, see our guide to clay soil problems in Texas.

Select fill vs structural fill vs fill dirt

These three names get used loosely, and suppliers do not always mean the same thing by them. Here is how the terms are generally used in DFW:

Fill dirtSelect fillStructural fill
What it isNative subsoil, usually clay or sandy claySandy clay / clayey sand meeting a PI specEngineered soil or granular material meeting a project spec
Typical PINot controlled (can be 30+ in DFW)Typically about 6–20Set by the engineer; often low
Swell potentialCan be highLowLow
Compacts to 95% Proctor?Sometimes, with effortYes, readily at the right moistureYes
Common usesFilling holes, pools, low spots, raising gradeUnder slabs, building pads, flatworkPads, retaining wall backfill, load-bearing fill
DFW delivered, starting at$10/yd$20/yd$20/yd
Denver delivered, starting at$15/yd$25/yd$25/yd

In practice, "select fill" is the North Texas term for a specific low-PI clay-sand, while "structural fill" is the broader term for any fill that meets an engineer's load-bearing spec. Many DFW soils reports use "select fill" for exactly the material other regions name structural fill. Our structural fill guide goes deeper on that side.

Where select fill gets used

  • Building pads for slab-on-grade homes. The most common use. The engineer specifies a thickness (often 1–3 feet, sometimes more) of select fill over prepared subgrade. See building pads.
  • Under driveways, patios and sidewalks where the flatwork sits on swelling clay.
  • Foundation repair backfill where the original backfill was native clay.
  • Shop and barn pads where a lighter version of the same idea saves cracks later.

Select fill is not the right material for a lawn or garden bed. It is lean in organic matter and compacts hard, so grass roots struggle in it. Cap it with screened topsoil if anything will be planted on top.

How select fill is placed and tested

Select fill only works if it is compacted. The usual sequence on an engineered pad:

  1. Strip vegetation and topsoil, then proof-roll or scarify the subgrade as the soils report directs.
  2. Place select fill in loose lifts, commonly 6–8 inches thick.
  3. Bring each lift to the specified moisture, usually near or slightly above optimum.
  4. Compact with a sheepsfoot or padfoot roller (or a plate/jumping jack in tight areas).
  5. Test each lift with a nuclear density gauge against the lab Proctor value, typically 95% for pads.

Our guides on Proctor testing and compacting fill dirt cover each step. Engineered pads are built to the soils report and the engineer's compaction spec: that document wins over any rule of thumb.

How much select fill do you need?

Multiply length × width × depth in feet, divide by 27 for cubic yards, then add 20–30% for compaction. Loose fill dumped from a truck compacts down significantly once it is rolled, so a pad that measures 100 compacted yards usually takes roughly 120–130 loose yards. Weight runs about 1.1–1.3 tons per cubic yard. The cubic yards calculator does the geometry, and the fill dirt calculator adds delivered pricing.

Pad sizeDepth (compacted)Compacted yd³Order (with ~25% extra)
20 × 30 ft (600 sq ft)12 in22~28 yd³
40 × 50 ft (2,000 sq ft)12 in74~93 yd³
40 × 50 ft (2,000 sq ft)24 in148~185 yd³
60 × 80 ft (4,800 sq ft)18 in267~333 yd³

Questions to ask before you order

  • What PI and LL range does the soils report require?
  • Does the engineer want lab results on the source material before placement?
  • What lift thickness, moisture range and compaction percentage are required?
  • Who is doing the field density testing, and how often?

If you have the spec in hand, include it in your order so the right source pit gets matched to it.

Order select fill

Text your address, yardage and the PI range from your soils report to (469) 253-2403 in DFW or (720) 577-5016 in Denver. Select fill starts at $20/yd delivered in DFW and $25/yd in Denver, in 10, 16 or 18-yard truckloads. Need the pad built, too? Send plans through the building pads bid form and we quote per job.

Need Fill Dirt Delivered?

Text us your project details for a quote in minutes.

Text for Instant Quote

Frequently Asked Questions

Select fill is a sandy clay or clayey sand with a controlled plasticity index, typically about 6 to 20 in North Texas specs. It compacts well and swells very little, so engineers specify it under slabs and building pads.

Fill dirt is native subsoil with no plasticity control, so in DFW it can be high-swell clay. Select fill is tested to meet a PI range and is meant for load-bearing use under foundations and flatwork.

Often, yes. In North Texas, select fill is the common name for low-PI sandy clay used as structural fill under slabs, while structural fill is the broader term for any fill that meets an engineer's load-bearing spec.

Select fill is delivered starting at $20 per cubic yard in DFW and $25 per cubic yard in Denver, with a 10-yard minimum order.

Not well. Select fill has little organic matter and compacts hard, so cap it with 4 to 6 inches of screened topsoil if you want a lawn on top.

Your project starts with
the right dirt.

Text us what you need. Quoted in minutes. Delivered in hours.

Text for instant quote

Mon–Sat 7am–5pm · Responses in minutes